موضوع: نگارش جدید riff jtag

Whats new :

CDMA Models JTAG support :

• Huawei C2605
• Micromax MMX 250C
• ZTE WP829
• LG RD3640

Bug fix updates :

• Samsung S5830
• HTC Incredible C

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

WHATS NEW!!!


- HTC Desire HD A9191 (HTC Ace) = Unbrick, IMEI, CID, ModelID, Simlock repair = WORLD FIRST ! ! !

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]


Firmware 1.25
---------------------------
- added 5.0V USB Power On/Off controlling feature
- changed sequence for 32-bit write accesses for ARM11 core (MSM8*** support)


JTAG Manager 1.33
---------------------------
- Improved connection policy:
Resurrection/DCC connection to device is implemented in such way that JTAG speed changes have 2 stages - booting stage and working stage.
Booting stage is the one from the connection start and until the DCC Loader upload is complete. Booting TCK/RTCK speed are setup
by JTAG Manager no matter what are the TCK settings by user (JTAG TCK Speed field in the JTAG Manager). Booting speed is hardcoded in the DLL.
After "booting" stage is complete, the "working" speed is set - the one which is selected by user in the JTAG TCK Speed field.
If Booting Speed in resurrector DLL is hardcoded as 'RTCK' the JTAG Manager would always use RTCK mode during booting stage.
Now policy is changed that is when user selects a fixed TCK frequency the JTAG Manager will automatically
change booting speed to the fixed TCK too.

- fixed bug: if "Use End Address" and "AutoFull Flash Size" were checked there was error setting valid length to read.

- for Advanced Users: advanced settings are now moved from the DCC Read/Write page ("Notifications...") into separate button on Box Service page (Advanced Settings button)

- added 5.0V USB Power On/Off controlling feature
For this go to Box Service page, click Advanced Settings: the Notifications dialog will be displayed,
go to "Advanced Settings" page and set desired mode for "Enable 5.0V output" checkbox.
When enabled, 5.0V power will be on after any "JTAG" operation executed and will remain "ON" until
box restart or until "Enable 5.0V output" checkbox is unchecked and any "JTAG" operation is executed.

- added optimization for flashing memory devices which are sector-based (like MDOC H3 or MMC/SD memory cards)

- if error code 0x3C (write-protect) is received no recover attempts are made.


[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]


Whats new:

• Motorola W200 full support
• Huawei C2801 full support
• Nokia 1006 full support

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Dont forget to check previous updates :

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید],

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]


[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]


Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:

• Solder JTAG cable to HTC WildFireS JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure HTC WildFireS is selected in the list of models;
• If you use battery, press Power On key;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

Following CDMA models are supported from today :

• Samsung B139 Repair/Unbrick, Read/Write NOR Flash
• Samsung B259 Repair/Unbrick, Read/Write NOR Flash
• Samsung B309 Repair/Unbrick, Read/Write NOR Flash
• Samsung B319 Repair/Unbrick, Read/Write NOR Flash
• Samsung B379 Repair/Unbrick, Read/Write NOR Flash
• Samsung B619 Repair/Unbrick, Read/Write NOR Flash
• Huawei C31 Repair, Read/Write NOR flash

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]

The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.

To resurrect Samsung T749:

• Solder JTAG cable to Samsung T749 JTAG pads;
• Connect USB cable;
• Make sure Samsung T749 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.

To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.

Resurrecting Samsung E189 is simple.

Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256

To resurrect Samsung E189:

• Solder JTAG cable to Samsung E189 JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure Samsung E189 is selected in the list of models;
• Click Resurrect button;
• Choose which areas to flash;
• Wait till software signals a successful operation completion;
• De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[برای مشاهده لینک ها شما باید عضو سایت باشید برای عضویت در سایت بر روی اینجا کلیک بکنید]